TravelBus (Logic & Protocol Analyzer)

{Acute} {Acute}

TravelBus (Logic & Protocol Analyzer)

  • PC-based, USB 3.0 interface/powered
  • 800 MHz timing / 200 MHz state analysis
  • Digital channels : 16 (Data), 1 (Clock), 2 (I²C/DP_AUX)
  • Memory : PC RAM
  • Real-time data and waveform display
  • Data logger

Buy

Specification (245.25 KB) Manual (2.19 MB)

Supported models for differential signal analysis without adapter:
DP_Aux: All TB3000 series
CAN2.0/CAN-FD: TB3016B Only
RS485: TB3016B Only

TB3000 Model Channels Module Protocol Decode Protocol Trigger
TB1016E  TB3016F  19  I 70+ I
 TB3016E  19  I, II 70+ I, II
TB1016B  TB3016B  25  I, II, III 70+ I, II, III

Protocol Decode: CAN FD, DALI2.0, DP_Aux, I²C, I²S, LIN2.2, PMBus, PWM, SMBus, SPI, MIPI I3C 1.1, UART, USB PD 3, ... (70+ decodes) 

Module I: I²C, RS232, SPI

Module II: HID over I²C, I²S, LIN2.2, MDIO, PMBus, SMBus, USB1.1

Module III: BiSS-C, CAN2.0B, CAN-FD, DALI2.0, Modbus, Profibus, RS422, RS485, USB PD 3, ...
 • Differential channels: 2 (CAN2.0B/CAN-FD), 4 (RS422/485)
 • Stackable with Acute TravelScope DSO to form an MSO
 • Isolated Ground: CAN2.0B/CAN-FD, RS485 (Safety Isolation >1000Vrms)

Introduction

TravelBus 3000 series is usually for Vehicle & Automation Industry measurement. It not only supports the common protocols such as I2C etc. but also supports measuring differential signals such as RS485(EIA485)、RS422、CAN2.0、CAN FD、DP-AUX etc. directly. In addition, the TB3000 series is a 2-in-1 analyzer( Logic Analyzer Mode & Protocol Analyzer Mode )

  • Logic Analyzer(LA) Mode
    Capture digital waveforms and support bus decodes. Able to stack with a DSO to form as an MSO.

    LA Storage Mode:
    Storage mode
    Long Time Record: Transitional Storage VS Compressed Storage
    For signal capture and analysis, usually require to record the signal for a long time. If the data is stored in a compressed way, it will cause your software to lag or even stop functioning when decompressing the data after it is sent back to the computer. Because PC memory size might insufficient for decompressed data size. To satisfy the requirement of smooth software operation and long-term recording without missing any data, the storage method adopted by the Acute analyzer is transitional storage rather than compression. After returning to the PC software, it doesn't need to do the decompression. The decoded results can be displayed while the analysis is finished. 

    Compressed enTransition en


    Software Main Window: LA MODE
    Trigger Settings Window:
    Trigger
    Multiple Protocols Analysis Simultaneously:
    Ex: I2C + USB PD3.0
    MultiProtocol
    TB3000 Stack With Other Vendors of Oscilloscope:
    (*Support DSO)SMBUS External DSO
    Stack DSO 1 Stack DSO 2

    Add Notes & Pictures in WaveformNote

    TravelBus Differential Signal Pin Define

    1. DP-AUX:

    DP AUXDPAUX PIN(*SDA->AUX+, SCL->AUX-)

    2. CAN 2.0B/CAN FD:

    CANIMG 20191113 130107(*Only for TB2016B)

    3. RS485(EIA 485)/RS422(EIA 422):

    RS485IMG 20191113 130143    (*Only for TB2016B) 
     
  • Protocol Analyzer(PA) Mode
    It is hardware decoding, may log protocol data very long time if without waveforms.
    Application timing: Preliminary protocol debug.

    PA Storage Mode:PA Storage Type

    Software Main Window:PA MODE

If you are looking for higher-speed digital signals, you can refer to other products:
TravelLogic 4000 series
MSO2000 series
LA3000+ series
BusFinder series

￭ Certification
CEFCC